AUT-PI120W
| Output | Group of Output | 1 | |
| DC Voltage | 48V DC | ||
| Default Output Voltage | 48.00-48.2V （VIN: 220VAC / LOAD: 0A） |
||
| Output Rated Current | 2.5A | ||
| Output Current Range | 0-2.5A | ||
| Output Rated Power | 120W | ||
| Total Peak Output Power | Up to 180W (Sustainable time 10S/220VAC) | ||
| Peak Output Current | 3.75A(Sustainable time 10S/220VAC) | ||
| Ripple noise | Peak - Peak ≤100mV (Test Method: The terminal shall be in parallel with capacitance of 0.1uF and 47uF, testing at 20MHz) |
||
| Output Regulation Range | DC47～56V | ||
| Stabilized Voltage Precision | ±1% (@ 90-264Vac input, 100% load) | ||
| Line Regulation | ±0.5% (@ 90-264Vac input, 100% load) | ||
| Load Regulation | ±1% (@ 90-264Vac input, 100% load) | ||
| Temperature Coefficient | ±0.03%/℃ | ||
| Output Start Time | < 2S @ nominal input (100% load) | ||
| Output Hold Time | > 20ms @ 115VAC, > 50 ms @ 230Vac (100% load) |
||
| Voltage Overshoot | ≤5% | ||
| Input | Input Voltage Range | 90~264VAC | |
| Input Rated Voltage Range | 100~240VAC | ||
| Frequency Range | 47Hz~63Hz | ||
| Rated Frequency | 50/60Hz | ||
| Starting Voltage | 90V AC | ||
| Efficiency | > 90.0% @ 115Vac, > 91.0% @ 230Vac | ||
| Input Current | < 2.20A @ 115Vac; < 1.10A @ 230Vac |
||
| Inrush Starting Current | < 35A @ 115Vac & 230Vac | ||
| Power Factor | > 0.99 @ 115Vac, > 0.93 @ 230Vac |
||
| Protection | Output | Over power | 144~180W Swing machine (Testing method: Increase the output current until enabling the protection. Protection mode: Swing machine, Self-recovery after over-power released.) |
| Over voltage | 57~70V V Swing machine (Short circuit the Pin1-2 of U8, swing machine. Output recovery to normal after removing the short circuit) Note: Do not use external voltage. |
||
| Over current | 3~3.75A Swing machine (Testing method: Increase theoutput current until enabling the protection. Protection mode: Swing machine, Self-recovery after over-current released.) |
||
| Short circuit | It achieves the long-term short circuit by connecting a sufficient cross-sectional area copper cable (Length at 15cm±5cm) with power output port. Self-recovery to normal after removing the short circuit. | ||
| Operation Environment | Operation Temperature and Humidity | -30～70℃; 20%～95%RH | |
| Storage Temperature and Humidity | -40℃~85℃; 10%~95%RH non-condensing | ||
| Liberation | Frequency range: 10 ~ 500Hz, Acceleration: 2G, Each sweep cycle 10min. Six sweeps along the X, Y, and Z axis |
||
| Surge | Acceleration: 20G, Duration time: 11mS, Three shocks along X, Y and Z axis |
||
| Altitude | 2000m | ||
| Safety andSafety andEMC Standard@25℃ | Security Standard | GB4943/EN60950 ■Reference □Certification |
|
| Dielectric Strength | Input—Output:3KVAC/10mA; Input--Case:1.5KVAC/10mA; Output---Case:0.5KVDC/10mA Time for each testing is 1min. |
||
| Grounding Test | Test Condition: 32A/2min; Ground bond:＜0.1 ohms. | ||
| Leakage Current | Input to GND ≤3.5mA; Input to output ≤0.25mA (Input 264Vac, 63Hz) | ||
| Insulation Resistance | Input—Output: 10M ohms; | ||
| EMI | Conducted Interference |
EN55022, EN55024, FCC PART 15 CLASS B | |
| Radiated Interference | EN55022, EN55024, FCC PART 15 CLASS B | ||
| Harmonic current | EN61000-3-2 CLASS D | ||
| EMS | Conducted Emission | EN61000-4-6 Level3 | |
| Radiated Emission | EN61000-4-3 Leve3 criterion B | ||
| Power Frequency Emission |
EN61000-4-8 Level3 | ||
| Electrostatic Emission | EN61000-4-2 Level4 criterion B | ||
| EFT | EN61000-4-4 Level4 criterion B | ||
| Surge | EN61000-4-5 Level4 criterion B | ||
| Dip and Interruption | EN61000-4-11 | ||
| Dimension (L*W*H) | 135*121*40mm | ||
